TFD-HW

Ten-Fourteen Door (TFD-HW) Hot Water Heated Air Curtains

Hot Water

The TFD is typically used over medium sized dock doors, or openings in an industrial environment and is equipped with a hot water coil on the intake. TFD units are manufactured in single increments that can be provided up to 14 ft. wide. The TFD has top and bottom access panels to replace or service motors or blowers without lowering entire unit or bottom half of unit. All industrial units are direct drive, which avoids misalignment of couplers and outboard bearings and eliminates periodic belt replacement. The motor/blower plate comes out as an entire piece and all parts on the outside of the unit are constructed of stainless steel.

At a Glance

Single Incremental Widths

4' to 14'

MAX Installation Height

14'

Heavy Duty Motors

1.5 HP

Key Design Features

  • All weight bearing structural support is made of formed 14-gauge stainless steel and galvanized steel. Outer casing is constructed of 18-gauge stainless steel.
  • TFD has heavy duty 1.5 HP motors at 1725 rpm each. Single speed.
  • Galvanized fans.
  • Air intake screen is perforated stainless steel.
  • Access panels for inspection, cleaning or removal of motor blower assembly, without having to lower the unit.
  • High efficiency discharge plenum with directional air foil vane factory set to facilitate deflection of air stream +/- 20˚.
  • Includes NEMA 12 control panel.

Recommended Controls

  • Panel mounted HAND / OFF / AUTO switch
  • Magnetic door switch for activation

360 View

360 View | TFD-HW - Ten-Fourteen Door (TFD-HW) Hot Water Heated Air Curtains

Cost Savings Calculator

This tool will help you understand the cost savings you could expect based on the air curtain you select and your input on how and where it will be used.

Calculate Now

Air Curtain Selector

This tool is designed to help you find the best air curtain
for your situation by asking a few basic questions.

Begin
TFD-HW | Performance Table
MODELNozzle
Width (in.)
Max. FPM
at Nozzle
Avg.
FPM
Max.
CFM
CFM at
Nozzle
Outlet Velocity
Uniformity
Number of
Motors
Motor
HP
Weight
(lbs.)
TFD-1-36HW36480040474214354195%11.5165
TFD-1-48HW48480030484232355693%11.5182
TFD-1-60HW60480024784301361492%11.5212
TFD-2-72HW72480040478426708295%21.5335
TFD-2-84HW84480034768445709793%21.5346
TFD-2-96HW96480030488463711292%21.5360
TFD-2-108HW108480027318532717091%21.5382
TFD-3-108HW10848004046126411062395%31.5500
TFD-3-120HW12048003647126591063894%31.5516
TFD-3-132HW13248003320126771065395%31.5526
TFD-4-144HW14448004047168551416495%41.5665
TFD-4-156HW15648003740168731417994%41.5681
TFD-4-168HW16848003476168911419495%41.5692
TFD-HW | Mechanical Information Table
MODELOverall
Width (in.)
Nozzle
Width (in.)
Mounting Width
Rear and Top (in.)
TFD-1-36HW393637.5
TFD-1-48HW514849.5
TFD-1-60HW636061.5
TFD-2-72HW75.0772.0773.57
TFD-2-84HW87.0784.0785.57
TFD-2-96HW99.0796.0797.57
TFD-2-108HW111.07108.07109.57
TFD-3-108HW111.15108.15109.65
TFD-3-120HW123.15120.15121.65
TFD-3-132HW135.15132.15133.65
TFD-4-144HW147.22144.22145.72
TFD-4-156159.22156.22157.72
TFD-4-168HW171.22168.22169.72